The bachelor thesis deals with the issue of machining materials of the ISO O group, which are not machined under normal conditions. The aim is to test the suitability of the application of tools from the manufacturers 6C Tools and UnionTool. Part of&#...

The bachelor's thesis contains a general analysis of the assembly procedures and their design characteristics, a description of the painting and spraying techniques used, the basic types of pumps used and their mechanisms, and an analysis of the parts for which the ...

The bachelor's thesis is focused on the construction of a fixture for clamping a universal chuck during milling. The thesis contains an introduction to the issue and a presentation of conventional clamping methods. Next, the procedure for constructing individual variants of clamping ...

The bachelor's thesis focuses on the development of milling technology for a given workpiece, with the automation of semi-finished product loading and subsequent manipulation of the workpiece during machining using a robotic arm. It consists of a theoretical section, a design of the...

The aim of this thesis is to provide insights into the machinability of 3D printed Inconel 718 compared to a conventionally manufactured version of this material. The theoretical part of the thesis describes the properties and microstructure of Inconel 718 and explains the 3D ...

The main objective of the bachelor thesis was to determine the effect of the size of the rake angle on the magnitude of the cutting resistance. After defining the individual concepts, the experiment had to be properly prepared (grinding jig, specially ground inserts, semi-finished&...

The aim of the thesis is to design the construction and production technology of a standardized component that can be used for automated production. The purpose is to create an illustrative example of automated production especially for teaching and demonstration purposes.

The bachelor thesis focuses on the theory of technological feasibility, assessment of technology and its influence on the selection of production technology. It also deals with the design modification of the component to improve the design manufacturability and the design of the product...

The bachelor's thesis contains information about the physical load of machine tool operators, the selection of risk factors at workplaces, measurement of forces (loads) at workplaces and the subsequent evaluation and assessment of the riskiness of the physical load of machine operators.

The bachelor's thesis deals with the problem of choosing the touch size for a 3D measuring machine. To find out how much inaccuracy will be caused by not following the relationship for choosing the touch size. Evaluation of the roundness of the di...

The bachelor's thesis deals with the risks of using metal powder for 3D printing. Above all, the attention is directed to the dustiness in their searched laboratory. The work describes changes in laboratory equipment and uses protective equipment to reduce the risks associated ...

The bachelor thesis examines the influence of Sinumerik system tools for feed rate control and their practical use. It describes the basic principle of operation of the CNC machine, feed control, acceleration behavior, interpolators and feed drives. The characteristics of the displacements&#...

The bachelor's thesis deals with the creation of metrological regulations in a medium-sized engineering company. The theoretical part consists of an analysis of the requirements of standards, determining the accuracy of measurement results and the methodology of compiling the metrological rul...

The bachelor thesis contains basic theoretical knowledge in the field of additive technologies with a focus on PBF-SLM (DMLS) and basic knowledge in hardfacing technology. The theoretical part deals with a component made of two materials, one of which is printed. In some cases,...

The bachelor thesis deals with the use of simulation of printing from metallic materials, application of topological optimization and subsequent simulation of the printing process. The aim of the bachelor thesis is the lightweighting of the specified components and the design of the...

The aim of the work is to transfer the program for flange machining from VISI SURF5 software to SolidCAM software and to rationalize the machining technology. The work deals with the issue of roughing, continuous 5 - axis machining and drilling automation.

This bachelor thesis contains experimental measuring of cutting forces. First the force was measured with standard toll clamping, then the tool was offset below the workpiece axis and after that these measurements were processed and finally compared with machining teory.

The main goal of the bachelor's thesis was to create a parametric program for a given type part from the company STREICHER, spol. s r.o. Pilsen. After designing different versions of the program, the individual variants are compared and the most advantageous program for St...

The theoretical part of the bachelor's thesis focuses on research in the field of cooling channels of cutting tools and on the modification of the cutting part of drilling tools. For inspiration and reflection, is viewed at the range of global engineering companies engaged ...

The bachelor thesis focuses on the analysis of the measurement process for a 3D measuring machine with using quality tools for quality control. The accuracy, repeatability, reproducibility and other properties of the 3D measuring machine are determined within the work.