Články / Articles (KMM) Domovská stránka kolekce Zobrazit statistiky

Procházet
Přihlásit se k zasílání denních e-mailů o novinkách RSS Feed RSS Feed RSS Feed
Záznamy kolekce (řazeno podle Datum zaslání v sestupně pořadí): 1 až 20 z 43
Novák, Petr , Nedvědová, Lucie , Kozák, Tomáš , Šotová, Petra , Bláhová, Olga , Jansa, Zdeněk , Medlín, Rostislav , Netrvalová, Marie , Minár, Jan
Investigation of carrier transport in ZnO and ZnO:Al thin films sputtered at different oxygen conditions

Undoped and doped zinc oxide in film form is used in a wide range of applications. Its electrical and optical properties depend on the oxide conditions during preparation, which are influenced by many deposition parameters. The aim of this work was to experimentally investigate...

Mohammad Reza, Shishesaz , Moslem, Ghobadi , Najmeh, Asadi , Alireza, Zarezadeh , Ehsan, Saebnoori , Hamed, Amraei , Schubert, Jan , Chocholatý, Ondřej
Surface Pretreatments of AA5083 Aluminum Alloy with Enhanced Corrosion Protection for Cerium-Based Conversion Coatings Application: Combined Experimental and Computational Analysis

The effects of surface pretreatments on the cerium-based conversion coating applied on an AA5083 aluminum alloy were investigated using a combination of scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), polarization testing, and electrochemical impedance spectroscopy. Two steps...

Čechura, Martin , Menšík, Petr , Bláhová, Olga , Vatansever, Atilla
Ojedinělý nález knižní spony ze Soběslavi, okr. Tábor

The subject of the paper is to inform about the new discovery of a book clip found using a metal detector on the outskirts of the town of Soběslav in the Tábor region. In addition to archaeological and historical evaluation, an element ana...

Bricín, David , Véle, Filip , Jansa, Zdeněk , Špirit, Zbyněk , Kotous, Jakub , Kubátová, Dana
The structure and the properties of WC-Co samples produced by SLM technology and carbon-doped prior to HIP processing

The purpose of this study is to verify how the carbon doping of the WC-Co cemented carbide (CC) affected their structure before their processing by hot isostatic pressing (HIP) technology. The samples for this experiment were fabricated by selective laser melting technology (SLM) u...

Bricín, David , Odehnal, Josef , Kříž, Antonín , Špirit, Zbyněk
Analysis of Defects Associated With Manufacturing Keys for Brass Musical Instruments

This article deals with the problematics of the production of small castings using gravitational investment casting. These are castings with a relatively complex shape, which are used as parts of trigger assembly for musical wind instruments. During their production, various defects occur&#x...

Čapek, Jiří , Kec, Jan , Trojan, Karel , Černý, Ivo , Ganev, Nikolaj , Kolařík, Kamil , Němeček, Stanislav
Fatigue Properties and Residual Stresses of Laser-Welded Heat-Resistant Pressure Vessel Steel, Verification on Vessel Model

Most power plants use the Rankine cycle, where the heat supplied to water and steam is converted into mechanical work; therefore, most components have to be made of heat-resistant steel. Sufficient mechanical properties must be ensured for welded pipes to meet stringent requirements.&#x...

Němeček, Stanislav , Trojan, Karel , Čapek, Jiří , Ganev, Nikolaj , Černý, Ivo , Kec, Jan
Hardening of Rail Vehicle Axles

The development of the technology for laser hardening of the axle seats of rail vehicles aims to improve the high-cycle service life of these axles under wheel pressing and thus to increase safety in rail transport. Laser hardening can create high compressive stresses that inc...

Průcha, Vojtěch , Bricín, David , Hájek, Jiří
Analysis of a Damaged Drill Made form HS 2-9-1-8 Steel

This article aims to explain the reasons leading to the damage of a drill during its final grinding. Metallographic analysis using light and scanning electron microscopy was used to determine whether the damage was related to the structure of the material, which is given by&#x...

Bricín, David , Kříž, Antonín , Novotný, Jan , Špirit, Zbyněk
The Effect of Boriding and Heat Treatment on The Structure and Properties of 100Cr6 Steel

The main aim of this case study is to present the changes caused by heat treatment on the structure and properties of 100Cr6 steel by annealing, hardening, and tempering in combination with previous chemical-heat treatment (CHT) by boriding. The boriding causes changes to the ...

Staszuk, Marcin , Reimann, Lukasz , Pakula, Daniel , Pawlyta, Miroslawa , Musztyfaga-Staszuk, Małgorzata , Czaja, Pawel , Beneš, Petr
Investigations of TiO2/NanoTiO2 Bimodal Coatings Obtained by a Hybrid PVD/ALD Method on Al-Si-Cu Alloy Substrate

This study aimed to investigate the influence of bimodal TiO2/nanoTiO2 coatings obtained in the PVD/ALD hybrid process on an Al-Si-Cu-type aluminium alloy on the physicochemical properties of the investigated materials. The reference materials were uncoated substrates and samples coated with...

Votava, Filip , Vrtáček, Jiří , Sýkora, Jindřich , Weinar, Michal , Jirková, Hana
Design of a Combined Tool for Sheet Tailoring during Press Hardening

Press hardening is used to produce complex parts by hardening them in a die. This results in martensitic structures with high strength values but low ductility. However, for real components, the combination of places with high strength or high ductility is required. One possibility...

Kiran, Abhilash , Li, Ying , Koukolíková, Martina , Brázda, Michal , Hodek, Josef , Urbánek, Miroslav , Džugan, Ján , Raghavan, Srinivasan , Odehnal, Josef
Elevated Temperature Baseplate Effect on Microstructure, Mechanical Properties, and Thermal Stress Evaluation by Numerical Simulation for Austenite Stainless Steel 316L Fabricated by Direct Energy Deposition

In the present study, the effect of material deposition at the elevated temperature baseplate on the microstructure and mechanical properties was investigated and correlated to the unique thermal history by using numerical simulation. Numerical results agreed well with the experimental results&#x...

Brabec, Josef , Ježek, Śtěpán , Beneš, Libor , Kříž, Antonín , Majrich, Petr
Suitability confirmation for welding ultra-high strength steel S1100QL using the RapidWeld method

This experiment assesses the suitability of square-welding high strength steel using the deep penetration welding method, RapidWeld. The aim of this method suitability assessment was to compare the final material properties of three welds, welded accordingly to identical welding procedures. High&...

Odehnal, Josef , Ludvík, Pavel , Studecký, Tomáš , Michálek, Pavel
Development of Universal Mould Geometry for the Teeming of Cylindrical Iron-Base Alloy Ingots

The presented work is aimed at developing a mould geometry suitable for casting both low- and high-alloy steel grades into 500 kg experimental ingots. The high Height-to-Diameter (H/D)-ratio mould currently used in COMTES FHT Inc. served as a reference and for finite element m...

Průcha, Vojtěch , Jansa, Zdeněk , Veselý, Vilém
Influence of deep cryogenic processing on carbide grain size in sintered carbide WC-Co

The paper deals with the change in carbide grain size of sintered WC-Co carbide after cryogenic pro-cessing. Because this structural parameter has a significant effect on mechanical properties. Some sources indicate that due to cryogenic processing takes place to reduce the size of ...

Bricín, David , Kříž, Antonín
Influence of the boriding process on the properties and the structure of S265 steel and X6CrNiTi18-10 steel

This investigation studied the changes in the microstructure of steels S265 and X6CrNiTi18-10 as a result of their chemical-thermal treatment by boriding. The steels were borided in Durborid boriding powder at 900 0C. During this process, surface layers of Fe-B borides formed in bo...

Bartoň Klufová, Pavla , Kříž, Antonín , Duliškovič, Josef , Vostřák, Marek
Composite laser claddings for corrosion protection of outer surfaces of storage containers for spent nuclear fuel in underground repositories

The present contribution examines the structures of and corrosion processes in copper-basalt compo-site laser claddings on a steel substrate. The cladding material was a laboratory-prepared mixture of the following components: Oerlikon METCO 55 (Cu > 99.9 %) and basalt powder. The metallo...

Hájek, Jiří , Dlouhá, Źaneta , Průcha, Vojtěch
Comparison of Industrial Quenching Oils

This article is a response to the state of the art in monitoring the cooling capacity of quenching oils in industrial practice. Very often, a hardening shop requires a report with data on the cooling process for a particular quenching oil. However, the interpretation of t...

Jeníček, Štěpán , Peković, Michal , Opatová, Kateřina , Vorel, Ivan
Relationship between Mechanical Properties in 42SiCr and 42SiMn Medium-carbon Steels and Austempering Temperatures

Sheet metal forming boundaries are established using the forming limit diagram (FLD). The Nakajima and Marciniak tests, which are based on stretching a material using a punch, are the most commonly used methods for determining the FLD or fracture forming limit diagram (FFLD). The&#...

Khalaj, Omid , Ghobadi, Moslem , Zarezadeh, Alireza , Saebnoori, Ehsan , Jirková, Hana , Chocholatý, Ondřej , Svoboda, Jiří
Potential role of machine learning techniques for modeling the hardness of OPH steels

This paper examines the influence of Johannes Crato and the seminal treatises on medicine and botany written by leading Central European scholars during the early modern period on the erudition and genesis of poetic work of the Elizabethan poet Philip Sidney. Johannes Crato (1519-1...

Záznamy kolekce (řazeno podle Datum zaslání v sestupně pořadí): 1 až 20 z 43