Full metadata record
DC poleHodnotaJazyk
dc.contributor.authorNovosád, Jan
dc.contributor.authorPeukert, Pavel
dc.contributor.authorPomp, Norbert
dc.contributor.authorKlouček, Pavel
dc.contributor.editorKučerová, Ludmila
dc.contributor.editorJirková, Hana
dc.contributor.editorJeníček, Štěpán
dc.date.accessioned2019-10-08T13:00:46Z-
dc.date.available2019-10-08T13:00:46Z-
dc.date.issued2019
dc.identifier.citationJIRKOVÁ, Hana ed.; JENÍČEK, Štepán ed. Proceedings PING 2019: modern trends in material engineering: 10.-13.09.2019, Pilsen. 1. vyd. Plzeň: University of West Bohemia, 2019, s. 92. ISBN 978-80-261-0879-5.en
dc.identifier.isbn978-80-261-0879-5
dc.identifier.urihttp://hdl.handle.net/11025/35262
dc.description.sponsorshipPING 2019 is organized with the support of funds for specific university research project SVK1-2019-002.en
dc.format1 s.cs
dc.format.mimetypeapplication/PDF
dc.language.isoenen
dc.publisherUniversity of West Bohemiaen
dc.rights© University of West Bohemiaen
dc.subjectvícefázecs
dc.subjectCFDcs
dc.subjectkalenícs
dc.subjectpolymercs
dc.titleCFD simulation of the multiphase heat transfer during the quenching processen
dc.typekonferenční příspěvekcs
dc.typeconferenceObjecten
dc.rights.accessopenAccessen
dc.type.versionpublishedVersionen
dc.description.abstract-translatedThe paper presents the results of the CFD simulation of quenching process for the ring shape sample. The aim of the work is to develop and validate the methodology for multiphase CFD simulation including the boiling during the quenching process. CFD simulation is provided in ANSYS Fluent. The Lee model is used for modelling the phase change during the quenching process. The first step consider the simulation of cooling of the ring sample when the correct model parameters will be found. Validation of results is performed by comparison with experimental data. Experimental was realized inside the own designed quenching bath device filled with quenching polymer. The general description of the experimental setup is included in the paper. The CFD results are cooling curves, i.e. variation of solid temperature on time. The Lee model parameters especially the evaporation frequency was tuned. Thin polymer film on the solid surface was considered to bring the results closer to the experimental data. The comparison between experiment and CFD shows very good agreement for higher temperatures, which covers the boiling stage. On the other hand for lower temperatures worse match of results was found caused probably by the sensitivity on the inlet velocity profile settings. Some recommendations for future work were defined.en
dc.subject.translatedmultiphaseen
dc.subject.translatedCFDen
dc.subject.translatedquenchingen
dc.subject.translatedpolymeren
dc.type.statusPeer-revieweden
Vyskytuje se v kolekcích:Proceedings PING 2019: modern trends in material engineering
Proceedings PING 2019: modern trends in material engineering

Soubory připojené k záznamu:
Soubor Popis VelikostFormát 
Novosad.pdfPlný text180,01 kBAdobe PDFZobrazit/otevřít
Zobrazit minimální záznam Zobrazit statistiky


Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam: http://hdl.handle.net/11025/35262

Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.

hledání
navigace
  1. DSpace at University of West Bohemia
  2. Publikační činnost / Publications
  3. Fakulta strojní / Faculty of Mechanical Engineering
  4. Publikace FST / Publications of FST
  5. Proceedings PING: modern trends in material engineering
  6. Proceedings PING 2019: modern trends in material engineering