Full metadata record
DC poleHodnotaJazyk
dc.contributor.authorValíček, Jan
dc.contributor.authorHarničárová, Marta
dc.contributor.authorŘehoř, Jan
dc.contributor.authorKušnerová, Milena
dc.contributor.authorGombár, Miroslav
dc.contributor.authorDrbúl, Mário
dc.contributor.authorŠajgalík, Michal
dc.contributor.authorFilipenský, Jan
dc.contributor.authorFulemová, Jaroslava
dc.contributor.authorVagaská, Alena
dc.date.accessioned2020-08-31T10:00:25Z-
dc.date.available2020-08-31T10:00:25Z-
dc.date.issued2020
dc.identifier.citationVALÍČEK, J., HARNIČÁROVÁ, M., ŘEHOŘ, J., KUŠNEROVÁ, M., GOMBÁR, M., DRBÚL, M., ŠAJGALÍK, M., FILIPENSKÝ, J., FULEMOVÁ, J., VAGASKÁ, A. Prediction of Cutting Parameters of HVOF-Sprayed Stellite 6. Applied Sciences, 2020, roč. 10, č. 7, s. [1-22]. ISSN 2076-3417.en
dc.identifier.issn2076-3417
dc.identifier.uri2-s2.0-85083483107
dc.identifier.urihttp://hdl.handle.net/11025/39569
dc.format23 s.cs
dc.format.mimetypeapplication/pdf
dc.language.isoenen
dc.publisherMDPIen
dc.relation.ispartofseriesApplied Sciencesen
dc.rights© MDPIen
dc.titlePrediction of Cutting Parameters of HVOF-Sprayed Stellite 6en
dc.typečlánekcs
dc.typearticleen
dc.rights.accessopenAccessen
dc.type.versionpublishedVersionen
dc.description.abstract-translatedIn this research, the authors set out to propose a new method of predicting and adjusting the main cutting parameters of chip machining, namely spraying on the substrate. In the experiments, a total of 28 turning cuts on a Stellite 6 coating layer were realized. The base materials of the Stellite 6 layers were EN S235JRG1 and carbide WC-Co. This work aimed to find out and optimize the influence of di erent combinations of cutting parameters. Due to the coating solution, the work is focused on the evaluation of the roughness Ra (m) of the turned substrate, the grain size Dgr (m) of the spraying, the normal stress rz (MPa), the residual stress rez (MPa), the specific cutting force Fc (N), the quality of adhesion to the substrate Adhmp (MPa) and other parameters. For the sake of a comprehensive solution to the problem, several new predictive equations and subsequent suggestions for solutions have been derived from this research topic based on the newly obtained experimental results. The proposed models and procedures make it possible to get new results and insights into coating technologies.en
dc.subject.translatedStellite 6en
dc.subject.translatedcoatingen
dc.subject.translatedmechanical parametersen
dc.subject.translatedpredictionen
dc.subject.translatedspraying technologyen
dc.identifier.doi10.3390/app10072524
dc.type.statusPeer-revieweden
dc.identifier.document-number533356200323
dc.identifier.obd43929903
dc.project.IDLO1502/RoRTI - Rozvoj Regionálního technologického institutucs
Vyskytuje se v kolekcích:Články / Articles (RTI)
OBD

Soubory připojené k záznamu:
Soubor VelikostFormát 
applsci-10-02524-v2.pdf4,98 MBAdobe PDFZobrazit/otevřít
Zobrazit minimální záznam Zobrazit statistiky


Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam: http://hdl.handle.net/11025/39569

Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.

hledání
navigace
  1. DSpace at University of West Bohemia
  2. Publikační činnost / Publications
  3. OBD