Full metadata record
DC poleHodnotaJazyk
dc.contributor.authorPolak, Marcin
dc.contributor.authorRadon, Adrian
dc.contributor.authorHawelek, Lukasz
dc.contributor.authorWlodarczyk, Patryk
dc.contributor.authorKaminska, Malgorzata
dc.contributor.authorOsadnik, Malgorzata
dc.contributor.authorJuszczyk, Barbara
dc.contributor.authorBurian, Wojciech
dc.contributor.authorKolano-Burian, Aleksandra
dc.contributor.editorKučerová, Ludmila
dc.contributor.editorJirková, Hana
dc.contributor.editorJeníček, Štěpán
dc.date.accessioned2019-10-08T10:20:59Z-
dc.date.available2019-10-08T10:20:59Z-
dc.date.issued2019
dc.identifier.citationJIRKOVÁ, Hana ed.; JENÍČEK, Štepán ed. Proceedings PING 2019: modern trends in material engineering: 10.-13.09.2019, Pilsen. 1. vyd. Plzeň: University of West Bohemia, 2019, s. 14. ISBN 978-80-261-0879-5.en
dc.identifier.isbn978-80-261-0879-5
dc.identifier.urihttp://hdl.handle.net/11025/35208
dc.description.sponsorshipPING 2019 is organized with the support of funds for specific university research project SVK1-2019-002.en
dc.format1 s.cs
dc.format.mimetypeapplication/PDF
dc.language.isoenen
dc.publisherUniversity of West Bohemiaen
dc.rights© University of West Bohemiaen
dc.subjectvýroba aditivcs
dc.subject3D tiskcs
dc.subjectslitiny mědi a cínucs
dc.subjectselektivní laserové tavenícs
dc.titleEffect of processing parameters on microstructure and properties of CuSn10P1 alloy fabricated by SLMen
dc.typekonferenční příspěvekcs
dc.typeconferenceObjecten
dc.rights.accessopenAccessen
dc.type.versionpublishedVersionen
dc.description.abstract-translatedThe interest in Cu-Sn alloys is associated with excellent flexibility, wear and corrosion resistance, and high mechanical strength. CuSn10P1 alloy has the widest applications among Cu-Sn alloys and is widely used in the shaft sleeve, bearing, gears, valves, etc. The properties of this alloy are strongly depended to the manufacturing process. Usage of the traditional casting causes the intergranular segregation and crystallization of primary α-Cu phase in a coarse mesh dendritic structure. This, in turn, manifest itself in poor properties, limiting its uses in industry. According to that new manufacturing methods should be used to improve the properties of this alloy. In this work, CuSn10P1 alloy was successfully produced using selective laser melting (SLM). The powder size was between 20-63 µm and its humidity during the process was lower than 5%. The four printing strategies were selected to investigate the impact of printing parameters on the microstructure and mechanical properties of the prints. The optimal processing conditions were chosen on the basis of optimization of laser power and scanning speed. The different process parameters result in the changes of the microstructure, especially porosity and the presence of microcracks. On the basis of the analysis of wavelength-dispersive X-ray spectroscopy, it was confirmed, that all chemical elements are evenly distributed after selective laser melting. The segregation of tin and copper can be also observed, however only under remelting of the same layer.en
dc.subject.translatedadditive manufacturingen
dc.subject.translated3D printingen
dc.subject.translatedCu-Sn alloysen
dc.subject.translatedselective laser meltingen
dc.type.statusPeer-revieweden
Vyskytuje se v kolekcích:Proceedings PING 2019: modern trends in material engineering
Proceedings PING 2019: modern trends in material engineering

Soubory připojené k záznamu:
Soubor Popis VelikostFormát 
Polak.pdfPlný text180,85 kBAdobe PDFZobrazit/otevřít
Zobrazit minimální záznam Zobrazit statistiky


Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam: http://hdl.handle.net/11025/35208

Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.

hledání
navigace
  1. DSpace at University of West Bohemia
  2. Publikační činnost / Publications
  3. Fakulta strojní / Faculty of Mechanical Engineering
  4. Publikace FST / Publications of FST
  5. Proceedings PING: modern trends in material engineering
  6. Proceedings PING 2019: modern trends in material engineering