Záznamy kolekce (řazeno podle Datum zaslání v sestupně pořadí): 81 až 100 z 238
|
Šulda, J.
,
Adámek, V.
,
Kroft, R.
Identification of viscoelastic material properties using the analysis of waves propagated in thin rods
|
|
|
Rosenberg, J.
,
Krejčová, M.
Fractional-order model of the Cajal-like interstitial cell
|
|
|
Rohan, E.
,
Lukeš, V.
Flow in poro-piezoelectric media induced by persitaltic deformation waves – homogenization approach
|
|
|
Rendl, J.
,
Smolík, L.
Influence of mesh density on the analysis of textured journal bearings
|
|
|
Plánička, S.
,
Rendlová, Z.
,
Švígler, J.
Screw expander: The expansion solver
|
|
|
Pecka, A.
,
Bublík, O.
Fluid-structure interaction algorithm for an elastic structure with large deformations
|
|
|
Moravcová, F.
,
Rohan, E.
Acoustic streaming of viscous fluid in a confining layer with vibrating walls – numerical simulations
|
|
|
Mandys, T.
,
Laš, V.
,
Krystek, J.
Influence of potting geometry of inserts load-carrying capability in sandwich structure
|
|
|
Lobovský, L.
,
Marešová, M.
,
Mandys, T.
,
Salášek, M.
,
Hluchá, J.
,
Pavelka, T.
,
Křen, J.
Computational modelling of pelvic ring osteosynthesis by minimally invasive fixation techniques
|
|
|
Jansová, M.
,
Malotín, T.
,
Křen, J.
,
Votápek, P.
,
Lobovský, L.
,
Hynčík, L.
Biomechanical comparison of five implants used to treat a supracondylar periprosthetic fracture of ostheoporotic femur
|
|
|
Hrabačka, M.
,
Bulín, R.
Form-finding of tensegrity structures based on defined topology and following semi-automatic creation of corresponding Simscape models
|
|
|
Heidler, V.
,
Bublík, O.
,
Pecka, A.
Eulerian-Lagrangian and Eulerian-Eulerian approaches for the simulation of particle-laden free surface flow
|
|
|
Dyk, Š.
,
Byrtus, M.
Frequency lock-in phenomenon in structures with aeroelastic couplings
|
|
|
Camprová Turjanicová, J.
,
Rohan, E.
Electrolyte flow through piezoelectric porous media and its application to two-scale cortical bone modeling
|
|
|
Bulín, R.
,
Hrabačka, M.
,
Hajžman, M.
Influence of various constraints in topology optimization of tensegrity structures using mixed integer linear programming
|
|
|
Zemčík, Robert
,
Zemčík, Hana
,
Krystek, Jan
,
Kroupa, Tomáš
,
Pihera, Josef
,
Prosr, Pavel
,
Komárek, Josef
,
Friedl, Jan
Experimental tests of braided composite tubes with Kapton tape
Kapton is a material developed by DuPont company. It is commonly used for insulation of electric and electronic devices. It offers excellent, physical, electrical, thermal and chemical resistant characteristics. It is a polyimide and it is usually available in a form of a homogeneo...
|
|
|
Mandys, Tomáš
,
Laš, Vladislav
,
Kroupa, Tomáš
,
Lobovský, Libor
Verification of the Hyperplastic Material Model with Damage for Woven Composites by Experimental Measurements Using Digital Image Correlation
The paper is aimed at testing the newly developed elasto-plastic material model with damage for the description of non-linear mechanical behaviour of the woven composites. Capabilities of the material model are verified by the usage of the experimental testing of the specimens with ...
|
|
|
Kaňáková, Sandra
,
Kottner, Radek
,
Krystek, Jan
,
Bońkowski, Tomasz
,
Heczko, Jan
Investigation of mechanical behaviour of commercially available polymeric materials and their suitability as impact absorber
A drop test was carried out to investigate mechanical behaviour of commercially available polymeric materials, namely expanded foams, polyurethane elastomers and urethane plastic. The Shore A hardness of presented material was verified. Moreover, the influence of the impact from higher position...
|
|
|
Heczko, Jan
,
Krystek, Jan
,
Kottner, Radek
Tensile Tests of 3D Printed PLA and Calibration of an Orthotropic Material Model
Tensile tests of a desktop 3D printed polylactic acid (PLA) material are presented. Four different angles of infill orientation were measured, all with the same infill density of 100 %. Poisson's ratios were determined in another set of tests using strain gauges and larger ...
|
|
|
Kottner, Radek
,
Kučerová, Karolína
,
Kochová, Petra
,
Bońkowski, Tomasz
Investigation of mechanical behaviour of LLDPE foil
LLDPE foil is commonly used for packing. Since this material allows large plastic deformations, it was suggested to use it as the main part of a new concept of safety systems for the automotive industry. A tensile test and an impact test with a spherical impactor wer...
|
|
Záznamy kolekce (řazeno podle Datum zaslání v sestupně pořadí): 81 až 100 z 238