The work is focused on laser shock peening technology. In the first part of the thesis are described principles, influences on material, usability and economic evaluation of technology. Methods for measuring residual stresses are also described. In the experimental part, the effects of&...

This thesis aims to optimize the deposition of the piezoelectric ZnO layer for use in a flexible piezo devices. There is introduction to technologies that acquire free energy from the environment and transform it into electrical energy in the introduction of this thesis. The n...

The diploma thesis contains the procedure of non-destructive ultrasonic evaluation of the steam generator collector welds using the phased array technique, theoretical and practical evidence of applicability and meeting of conditions given by the nuclear power plant operator. Evidence of the ...

This thesis deals with influence of mechanical loading on microstructural changes of heat resistant high chrome steel COST F. Tests of LFC and LFC+creep at temperature 600 °C were performed. Development of chromium carbides and precipitation of Laves phase were investigated. Using quant...

Aim of this master's thesis is to create higher dispersion of formed nitrides by use of cryogenic treatment in nitriding process. This should lead to better wear resistance, corrosion resistance a better toughness and hardness of nitriding layer. Use of cryogenic heat treatment ...

This thesis consist describing of zirkonium and their alloys. Also deals with the question of phase transformation with low and high-temperature exposure.especially in relation to the accident of nuclear reactors called LOCA (Loos-of-coolant-accident). Experimental program is focused on the evaluation...

This thesis deals with the decarburization of the poured tests of castings which are subsequently used for test samples for the mechanical properties and which are provided to custumer with required část. In the theoretical part of this thesis is given all necessary backround ...

The master's thesis focuses on the use of high speed cameras in the field of welding. The aim is to obtain a high speed record of the welding process from the orbital welding of stainless steel tubes by the TIG method. An analysis of this welding...

The main objective is to compare microstructures and properties of spring steel 54SiCr6 after two different types of spheroidising treatment. In the introduction, type of springs steel are characterized and descriptions are given of their heat treatment. Effects of heat treatment on the...

This diploma thesis deals with the robotization of welding processes by determining the appropriate technological process for the welding of 2 mm thick stainless steel austenitic steels used for the production of pressure tanks. The theoretical part focuses on suitable welding technology...

The aim of the DP is to develop a procedure for the evaluation of the micro-cleanness of steels with increased fatigue strength achieved by reducing the number of inclusions by the method: Based on the measured values of the non-metal inclusions sizes by means of the ...

This diploma thesis is focused on evaluation of the contribution of thin film to increase corrosion resistance of shrink fit chucks. The samples with thin film are compared to conventional shrink fit chucks with mass finishing surface and shot peened surface samples. Diploma thesis...

This diploma thesis deals with the lifetime of dissimilar welded joints in the conditions of the secondary circuit of VVER. The theoretical part describes the problems associated with corrosion resistance of dissimilar welded joints and degradation processes, which significantly affect their ...

The presented diploma thesis is focused on application of the laser surface remelting technology onto of HVOF sprayed hardmetal-based coating. The Cr3C2-25%CoNiCrAlY thermal sprayed coating was melted by a high powerdiode laser. The microstructure of the heat-affected coating was examined by ...

This thesis focuses on 3D printing of sintered carbides by SLM technology - Sintering Laser Melting and builds on experiments from abroad. The purpose of this thesis was to make sintered carbide using SLM technology and to perform porosity and corrosion resistance testing. Next,&#x...

The focus of this work is to state the basics of the individual NDT methods used, their possibilities of use, advantages and disadvantages. It also contains a comparison of these methods and refers to calibration and test samples. The experimental part consists of testing vari...

The diploma thesis deals with the preparation and evaluation of organic-inorganic coatings and films with different types of fillers, which could be used in the field of packaging tech-nology. The main objective is to select the most suitable al-ternative from a selection of select...

The diploma thesis deals with the preparation of biodegradable material based on cellulose and thermoplastic starch. Background of thesis is based on knowledge about paper pulp manufacturing process and composition. There is a way how to get hydrofobic properties and higher tensile stre...

The aim of this diploma thesis is to verify under laboratory conditions that the application of UDDG as a filler in a metallic nickel matrix coating made by galvanic plating can increase the abrasion resistance of this composite coating compared to the nickel coating itself.

This thesis solves the new method of repair of welds. This method of repair is named WOL (overlay). The new method is more economical and cheaper than current method. The principle of the WOL method is the overlay weld on original weld, where the defect is indicated....